 |
 | |
- The 694 Series Flow Restrictor Valve incorporates a 1/4” NPT Polypropylene Body and Flow Restrictor insert that operates as a flexible orifice to provide reliable flow regulation from .07 to 3.96 Gallons Per Minute.
- Minimum inlet pressure is 15 psi to reach metered flow rate.
- Maximum inlet pressure is 125 psi.
- All materials are NSF Approved under Standard 61.
|
|
|
|
|
 | |
- The 693 Series Flow Restrictor Valve incorporates a 3/8” NPT Polypropylene Body and Flow Restrictor insert that operates as a flexible orifice to provide reliable flow regulation from .07 to 3.96 Gallons Per Minute.
- Minimum inlet pressure is 15 psi to reach metered flow rate.
- Maximum inlet pressure is 125 psi.
- All materials are NSF Approved under Standard 61.
|
|
|
|
|
 | |
- The 685 Series Flow Restrictor Valve incorporates a 1/2” NPT Polypropylene Body and Flow Restrictor insert that operates as a flexible orifice to provide reliable flow regulation from .26 to 3.96 Gallons Per Minute.
- Minimum inlet pressure is 15 psi to reach metered flow rate.
- Maximum inlet pressure is 125 psi.
- All materials are NSF Approved under Standard 61.
|
|
|
|
|
 | |
- The 687 Series Flow Restrictor Valve incorporates a 3/4” NPT Polypropylene Body and Flow Restrictor insert that operates as a flexible orifice to provide reliable flow regulation from .26 to 3.96 Gallons Per Minute.
- Minimum inlet pressure is 15 psi to reach metered flow rate.
- Maximum inlet pressure is 125 psi.
- All materials are NSF Approved under Standard 61.
|
|
|
|
|
 | |
- The 555 Series Off Line Balanced Pressure Regulator is designed for carwash and pressure wash applications where a weep gun is used or bypass can be returned to the supply tank.
- The 555 Series Off Line Regulator is available in three standard spring pressure ranges to 2000 psi and can be used in systems with more than one outlet.
- The 555 Series Off Line Regulator mounts to a “T” from the pump outlet and is repairable.
- Buna-N, Ethylene Propylene and Fluoroelastomer (Viton®) seals are available for chemical compatibility.
|
|
|
|
|
 | |
- The 556 Series In Line Balanced Pressure Regulator is designed for carwash and pressure wash applications where a weep gun is used or bypass can be returned to the supply tank.
- The 556 Series In Line Regulator is available in three standard spring pressure ranges 2000 psi and can be used in systems with more than one outlet.
- The 556 Series In Line Regulator mounts to the pump outlet and is repairable.
- Buna-N, Ethylene Propylene and Fluoroelastomer (Viton®) seals are available for chemical compatibility.
|
|
|
|
|
 | |
- The 579 Series Off Line Balanced Pressure Regulator is designed for carpet cleaner and small pressure wash applications where a weep gun is used or bypass can be returned to the supply tank.
- The 579 Series Off Line Regulator is available in two spring pressure ranges of 500 and 1000 psi and can be used in systems with more than one outlet.
- The 579 Series Off Line Regulator mounts to a “T” from the pump outlet and is repairable.
- Buna-N, Ethylene Propylene and Fluoroelastomer (Viton®) seals are available for chemical compatibility.
|
|
|
|
|
 | |
-
The 003 Series Unloader is designed is for low pressure cold water pressure wash applications.
-
The 003 Series Unloader traps pressure in the line when the spray gun is closed.
-
The bypass port opens and fluid flows back to the inlet side of the pump or reservoir, allowing the pump to run under significantly reduced pressure.
-
When the spray gun is opened, the bypass port closes and fluid is directed downstream to the nozzle.
-
The 003 Unloader is tested for performance but not preset for pressure.
-
Start with the Unloader at its lowest spring tension.
-
Raise pressure by turning the adjusting ...
|
|
|
|
|
 | |
- The 498 Series Pressure Limiting Valve is designed for specific combinations of volume and pressure to fit the exact end use application.
- The 498 Series Pressure Limiting Valves are non-adjustable, tamper proof and will operate in any orientation.
- The system pressure will drop to approximately 50% of the Maximum Operating Pressure when the 498 is in By-Pass mode.
- The 498 Series Pressure Limiting Valve can be used as a Safety Valve “popping-off’ at the threshold pressure and reseating after the system pressure returns to normal.
- Always select a valve with a pop-off pressure at least 100 psi above the maximum operating pressure.
- The 498 will operate ...
|
|
|
|
|
 | |
- The SMC HI-LO Nozzle design covers 1/8" cold water applications for use with a downstream injector, like the SMC 588 Chemical Injector.
- The HI-LO Nozzle adjusts from low pressure (20 psi - 100 psi) for chemical injection, to high pressure (1200 psi) for clear rinse.
- Change from soap to high pressure rinse, at a 20 degree spray angle flat pattern, with a turn of the nozzle cap.
- The Hi-Lo Nozzles are sized and stamped with a gallons per minute rating as measured at 40 psi.
- For example, a .65 Hi-Lo would flow .65 GPM @ 40 psi and 3.3 gpm @ 1000 psi.
- Consult the attached chart to select the nozzle size for the system capacity.
|
|
|
|
|
 | |
- The ST Series Nozzle design incorporates a Stainless Steel Tip in a Nickel Plated Brass Body.
- The ST Series Nozzle is available in 1/8 and 1/4 Male or Female NPT, and the Long Tee to fit a standard Nozzle Compression Nut.
- The three ST Nozzle flow patterns are 0 Degree Straight Stream, 20 Degree Flat Fan and 40 Degree Flat Fan.
- The ST Nozzles are sized and stamped with a gallons per minute rating as measured at 40 psi.
- For example, a .65 ST Nozzle would flow .65 GPM @ 40 psi and 3.3 gpm @ 1000 psi.
- Consult the attached chart to select the nozzle size for the system capacity.
|
|
|
|
|
 | |
- The SMC Sprayflex Nozzle design covers 1/8" and 1/4" applications.
- The Sprayflex is a variable pattern nozzle from a O-Degree Straight Stream to 80-Degree Flat Fan.
- The Sprayflex is available in the standard brass cap or polyester cap for hot water applications up to 1500 psi.
- The Sprayflex Nozzles are sized and stamped with a gallons per minute rating as measured at 40 psi.
- For example, a .65 Sprayflex would flow .65 GPM @ 40 psi and 3.3 gpm @ 1000 psi.
- Consult the attached chart to select the nozzle size for the system capacity.
|
|
|
|
|
 | |
- The SMC 588 Chemical Injector design covers 3/8" downstream injection applications.
- The 588 Injector is ideal for use with the SMC 433 Series Hi-Lo Nozzle.
- A check valve built into the injection barb keeps high pressure rinse water from flowing into the chemical container.
- The 588 Injector draws chemical when pressure drops through the venturi and the injection barb check valve opens.
- The rate of injection is controlled by inserting the included metering orifices into the injection barb.
- Three set rates can be achieved:
- No Orifice (28 Ounces per minute)
- .035 Black Orifice (10 Ounces per minute)
- .029 Brass ...
|
|
|
|
|
 | |
- The 515 Series Thum-Gun is designed for comfort and ease of operation.
- The natural position of the vinyl covered handle and easy action thumb operated trigger minimize user fatigue.
- The 515 Thum-Gun features a shielded trigger with safety lock to prevent accidental trigger operation.
- The standard 515 Thum-Gun is rated to 1500 psi and incorporates a stainless ball on a stainless seat which requires approximately 200 psi minimum operating pressure to seal.
- A Soft Viton® Seat option is available for applications under 500 psi where a positive shut off is required.
- Seal, Soft Seat and Hard Seat Repair Kits are available, economical and easy to ...
|
|
|
|
|
 | |
- The 711 Series Rolover Valve promotes multiple configurations to fit the exact end use application.
- The 711 Rolover comes standard with a 90 Degree Elbow and is commonly used as a selector valve allowing the user to switch easily between two different spray nozzles.
- The 711 Rolover on a typical pressure wash application would utilize the economical SMC S/T Series Nozzles using a high pressure narrow pattern stream for wash and low pressure wide pattern stream for rinse.
- Combining the 711 Series Rolover with the SMC 588 Injector and S/T Series Nozzles allows for easy selection between a low pressure soap application and high pressure rinse.
|
|
|
|
|
 | |
- The 713 Rolover is available with a 1/4" Female NPT or 11/16-16 Swivel Nut Inlet and 11/16-16 Nozzle Thread Outlets.
- The 713 Rolover is commonly used as a selector valve allowing the user to switch easily between two different spray nozzles in an agricultural or industrial application.
- The standard configuration comes with one of the Outlet Nozzle Thread Nuts nickel plated and the other is brass for identification of the active nozzle.
- See our catalog information on the ST Nozzle (Long Tee body style) for an economical nozzle tip for the 713 Series Rolover Valve.
|
|
|
|
|
 | | (12)
- The 667 Series Relief Valve incorporates a guided piston and large flow area design for full flow with minimum pressure loss.
- The 667 Series Relief Valve is available with a T-Style Adjustment Handle or a Screw Slot with Wire Lock-Out Stop Nut.
- The 667 Relief Valve is available with a choice of two spring pressure ranges to 250 psi and can be used in systems with more than one outlet.
Search 667 Relief Valve - 12 Items |
